<video id="vfpb3"><meter id="vfpb3"></meter></video>

    <address id="vfpb3"><ruby id="vfpb3"></ruby></address>

    <var id="vfpb3"><font id="vfpb3"></font></var>

    <menuitem id="vfpb3"><dfn id="vfpb3"></dfn></menuitem>
      <big id="vfpb3"><big id="vfpb3"></big></big>
      <sub id="vfpb3"></sub>

            <pre id="vfpb3"></pre>
            網站首頁新聞動態產品中心公司資質關于我們合作伙伴
            首頁產品中心DJM產品  
            高錳鋼陶瓷復合齒板
            來源: 點擊數:3810次 更新時間:2019-6-15 10:27:57
            詳細簡紹:

            北京金煤創業科技股份有限公司主營金屬陶瓷復合鑄造耐磨件,產品包括:高錳鋼陶瓷復合齒板,高錳鋼陶瓷復合扎臼壁,圓錐襯板,高鉻陶瓷復合板錘,馬氏體鋼陶瓷復合錘頭,合金鋼陶瓷復合自磨機/球磨機襯板,高鉻陶瓷復合立磨滾套,碾底襯板等。

             

            DJM 陶瓷復合鄂式碎機備件(齒板)技術介紹

            DJM ceramic composite jaw crusher spare parts (jaw plate) technology introduction

            顎式破碎機的工作部分是兩塊顎板,一是固定顎板(定顎),垂直(或上端略外傾)固定在機體前壁上,另一是活動顎板(動顎),位置傾斜,與固定顎板形成上大下小的破碎腔(工作腔);顒宇板對著固定顎板做周期性的往復運動,時而分開,時而靠近。分開時,物料進入破碎腔,成品從下部卸出;靠近時,使裝在兩塊顎板之間的物料受到擠壓,彎折和劈裂作用而破碎。顎式破碎機目前廣泛使用的齒板多是采用高錳鋼制造。由于物料的沖刷,破碎過程中的擠壓,碾磨作用,造成齒板磨損嚴重,針對這一情況,DJM 選用高錳鋼為基材的陶瓷復合材料,即齒板的基體采用高錳鋼,同時在基體上嵌鑄具有高耐磨性的陶瓷隨形加強筋,在保持高錳鋼原有的加工硬化耐沖擊性能的同時提高了高錳鋼的耐磨強度,陶瓷復合材料齒板的壽命約為高錳鋼齒板的2倍以上。

            Work part of the jaw crusher is two pieces of jaw plate, one is the fixed jaw plate (fixedjaw), which is vertical (or the upper slightly extraversion) fixed in front of the body wall, the other is movable jaw plate (movable jaw),which is tilt, form big end dowm crushing cavity (work cavity). movable jaw plate press the fixed jaw plate with periodic reciprocating motion, sometimes separately, sometimes near. Separately, material into the crushing cavity, finished products discharge from the lower ; Approached, the materials are squeezed between two pieces of jaw plate, bending and fracturing effect to broken. Jaw crusher is widely used high manganese steel manufacturing . Due to the material erosion, the extrusion process broken, grinding effect, cause plate wear serious, in order to solve this situation, DJM chooses high manganese steel as base material of the ceramic composite materials, which is plate basement with high  manganese steel and then embed the high wear resistance With stiffener into the basement.below keeping original work hardening of high manganese steel impact resistance performance  and improving wear resistance strength at the same time, the life of the ceramic composite  plate is about 2 times longer than the high manganese steel basement plate.

            Product include: Mn18Cr2+Ti-Re  Mn18Cr2  Mn13  Mn13Cr2  Martensite steel

            附圖-2高錳鋼陶瓷復合齒板外觀示意圖

            Picture-2  High Mn ceramic composite jaw plate external view

             

            【刷新頁面】【加入收藏】【打印此文】 【關閉窗口】
            上一篇:陶瓷復合圓錐襯板 下一篇:高錳鋼陶瓷復合軋臼壁
              友情鏈接:   DJM-CASTING & FORGING  |  波紋補償器 |  bjjm-bj |  sauter-cn
            環球破碎機網淘寶動態評分SCR脫銷蓄熱式焚燒爐叉車尾氣凈化
            高鉻陶瓷復合_陶瓷復合鑄造_高錳鋼陶瓷復合 - 北京金煤創業科技股份有限公司 2016-2020 @ All Rights Reserved 京ICP備16053533號-1
            郵件:info@djm-bj.com 聯系電話:010-88909291  地址:北京市石景山區古盛路36院1號樓14層1403